Ortec X-Cooler II PopTop connector, 110 VAC, DOES NOT COOL, AS IS

Description

Ortec X-Cooler II PopTop connector, 110 VAC, DOES NOT COOL, AS IS
This is a
Ortec X-Cooler II PopTop connector, 110 VAC, DOES NOT COOL, AS IS
.
What you will get:
Ortec X-Cooler II PopTop connector, 110 VAC, DOES NOT COOL, AS IS
This is my item 1006.  1 was available at listing time.
The label that shows information says:
Compressor Oil 3GS
Viscosity 150 SUS (ISO32)
SUNISO (L318)
Mixture # MX1042
Installation 8/2006
Another label says
Part No. AF0343-011
Model No. CC2402-1
Power Input 115VAC 60 HZ
Serial No. 060807 KA
About this X-Cooler II:
This was purchased at an auction with a whole lot of other items.
When this was powered on, the unit did not cool.  I am sure the compressor was running.
I did contact Ortec and they told me the following:
Unfortunately, the entire X-Cooler product line (X-Cooler I, II, III) has been obsoleted and is no longer supported. You can attempt to reach out to the company who used to build these for ORTEC to see if they can be of help.
And I did look up MMR and the web site is no longer registered to them, and I am guessing they went out of business.
This is in it's own Plastic Shipping Crate.  The size is  40" x 26" x 27" and it weighs 110 Pounds.  It was shipped via UPS at one time and I'm guessing the price was up there.
Since it didn't cool and I didn't get any more information that would help me get this cooling, so it is sold as is.
You are welcome to pick this up in Natick, MA
Check out my
other items
where I have a lot of other scientific equipment and accessories for sale.
More Information:
Replace Liquid Nitrogen with the New X-COOLER II
•
More Powerful than Ever
•
No Limit to Detector Size
•
For HPGe Detectors within a Wide Range of Gamma Spectroscopy Applications
•
Compatible with All ORTEC HPGe Detector Types
•
Lightweight and Compact Design
•
Low Power Operation (less than 400 W)
•
Field Replaceable: Retrofits to Existing Detectors and is Easily Maintained
•
Cool HPGe Detectors Anywhere There’s Electricity!
•
No Dewar Filling Operations
•
No LN
2
Safety Hazard
•
No Bulky Storage Tanks or Unwieldy Plumbing Systems
•
A Truly Economical Alternative to Liquid Nitrogen
Introducing X-COOLER II
Now There is No Limit to the Size of
Detector that can be Cooled by
Mechanical Cooling. . .
There is virtually no limit to the HPGe laboratory
applications that can be optimized by mechanical cooling
with the new X-COOLER II. This exciting new product
extends the capability of mechanical cooling to any size
detector!
That’s right. . . any size detector!
The use of LN
2
has truly become a thing of the past!
. . . and you’ll save money, time, and operating costs!
The annual cost of running an X-COOLER II can actually
be less than that of an LN
2
-cooled detector.
A Variety of Detector Options
X-COOLER II is designed to work with any ORTEC
detector available in PopTop configurations. Degradation
of resolution performance is guaranteed to be less than
10% for energies less than 500 keV, and no degradation
will be observed above 500 keV.
Light on
X-COOLER II is not only inexpensive to purchase and
operate, but it is smaller and lighter than other devices of
this type. The compact design boasts a footprint of less
than one square foot (or 930 cm
2
), stands 11” (28 cm)
tall, and weighs less than 36 pounds (16.4 kg). This
compares very favorably to the previous generation of
mechanical coolers.
Field Replaceable
Reliability and ease of service are essential to any
mechanical cooling system for HPGe detectors.
X-COOLER II systems employ the ORTEC patented
1
PopTop™ detector capsule technology. While the design
life of the X-COOLER II is greater than five years, there is
always the possibility of failure of any mechanical system.
Because of the unique PopTop design of ORTEC
detectors, an X-COOLER II can be replaced in the field,
without special tools or procedures. After the detector has
returned to room temperature, a new X-COOLER II can
be installed in less than 10 minutes. The detector does
not have to be returned to the factory to replace a faulty
mechanical cooling system.
Retrofittable
The X-COOLER II can be retrofit in the field to existing
PopTop detectors. Simply warm the existing detector,
unscrew the capsule from the LN
2
cryostat, and couple
onto the new X-COOLER II.
You’ll be up and running in no time!
Proven Technology
Traditional mechanical coolers fail because oil from the
compressor mixes with the refrigerant, migrating to the
heat exchanger and clogging it, thus causing the detector
to warm up. The X-COOLER II's patented design cleans
the oil out of the refrigerant continuously. Similar coolers
using this design have logged over 38,000 hours (more
than 4-1/4 years) of operation without failure... and still
going.
Specifications
*
Resolution:
Detector specifications are warranted to
no
degradation above 500 keV and less than 10%
degradation of the warranted and published LN
2
specifications at less than 500 keV.
Mechanical:
Dimensions:
Compressor: 12.5” W x 12.5” D x 11” H
(31.8 cm x 31.8 cm x 28 cm)
Cold Head Length with Detector Capsule
Standard: 23.25” (59 cm)
Oversize: 24.5” (62.3 cm)
Ultra: 25.5” (64.8 cm)
Weight:
Compressor: 36 lbs. (16.4 kg)
Cold Head: 11 lbs. (5 kg) not including capsule
Noise:
Less than 70 dB at 1 meter
Input Power:
110–120 V ac, 57–63 Hz or
220–240 V ac, 47–53 Hz (input power must be
selected by choosing the appropriate model number,
see ordering information)
Power Consumption: <
500 W during initial cool
down. <400 W during normal operation.
Connector Hose:
10 ft. gas hose connected
between compressor box and cold head assembly is
included. Longer lengths available on special request.
Contact the factory for more information and pricing
on other hoses.
Refrigerant:
Mixed gas, CFC-free refrigerant.
MSDS available on request.
CE Approved
Please use the shipping calculator to determine shipping.
Check out my
other items
!
If you receive your item and it is not to your 100 Percent Satisfaction, please contact us before leaving feedback.
I strive to make sure every transaction is a positive one!
IF you have a problem with my item, I would like you to use the "Contact Seller" link in the listing, or call me. Please don't open a case. Cases count against me even if they are resolved.
I stand behind my items and will work out any problems that you may have with an item.
So please contact me if you have a problem with an item I have sold you and don't use the eBay Case as a means of communication.
International Buyers, Please Note: Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up do not confuse them for additional shipping charges. We do not mark merchandise values below value or mark items as "gifts". US and International government regulations prohibit such behavior.
Powered by SixBit's eCommerce Solution